▒DDR Version V1.08 20210825
DDR3, 328MHz
BW=16 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=1024MB
change to: 328MHz
change to: 528MHz
change to: 784MHz
change to: 1056MHz(final freq)
out
U-Boot SPL board init
U-Boot SPL 2017.09-gc6ee75eec1-210728 #zzz (Sep 13 2021 - 10:36:14)
unknown raw ID phN
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
Magic is incorrect.
Error validating A/B metadata from disk. Resetting and writing new A/B metadata to disk.
SPL: A/B-slot: _a, successful: 0, tries-remain: 7
## Verified-boot: 0
## Checking optee 0x08400000 (gzip @0x08600000) ... sha256(8535dc6b96...) + sha256(3956029bbb...) + OK
## Checking uboot 0x00600000 (gzip @0x00800000) ... sha256(486b99b935...) + sha256(2d6eb39918...) + OK
## Checking fdt 0x006b7220 ... sha256(7b8a0e51c0...) + OK
Jumping to U-Boot(0x00600000) via OP-TEE(0x08400000)
Total: 208.138 ms

I/TC:
I/TC: cpu feature:0x0
I/TC: RV1126 SoC
I/TC: cpu_st=0xe0
I/TC: Next entry point address: 0x00600000
I/TC: OP-TEE version: 3.13.0-655-g317f8b06b #derrick.huang (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05)) #1 2022年 10月 24日 星期一 10:08:19 CST arm
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot


U-Boot 2017.09 (Mar 25 2024 - 09:21:13 -0700)

Model: Rockchip RV1126 Evaluation Board
PreSerial: 2, raw, 0xff570000
DRAM:  1021.7 MiB
Sysmem: init
Relocation Offset: 00000000
Relocation fdt: 3bbfa010 - 3bbfedf0
CR: M/C/I
Using default environment

no mmc device at slot 1
GUID Partition Table Header signature is wrong: 0x900D2F47CF1D42BB != 0x5452415020494645
Repair the backup gpt table OK!
Found IDB in SDcard
dwmmc@ffc50000: 0, dwmmc@ffc60000: 1 (SD)
Bootdev(atags): mmc 1
MMC1: Legacy, 52Mhz
PartType: EFI
boot mode: recovery (misc)
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
I2c0 speed: 400000Hz
PMIC:  RK8090 (on=0x10, off=0x00)
vdd_npu_vepu 800000 uV
vdd_arm 800000 uV
io-domain: OK
Warn: can't find connect driver
stdio_add_devices: Video device failed (ret=-19)
Model: rp-rv1126
rp_power not have children !
rp_power have node!
rp_power: vdd5v_3v3 gpio set output
rp_power: hub_rst gpio set output
rp_power: usb_5v gpio set output
rp_power: spk_on gpio set output
rp_power: spk_mute gpio set output
CLK: (uboot. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
  apll 816000 KHz
  dpll 528000 KHz
  gpll 1188000 KHz
  cpll 500000 KHz
  hpll 1400000 KHz
  aclk_pdbus 500000 KHz
  hclk_pdbus 198000 KHz
  pclk_pdbus 99000 KHz
  aclk_pdphp 297000 KHz
  hclk_pdphp 198000 KHz
  hclk_pdaudio 148500 KHz
  hclk_pdcore 198000 KHz
  pclk_pdpmu 99000 KHz
Net:   eth0: ethernet@ffc40000
Hit key to stop autoboot('CTRL+C'):  0
## Booting FIT Image at 0x3aca1c00 with size 0x00d55400
Fdt Ramdisk skip relocation
## Loading kernel from FIT Image at 3aca1c00 ...
   Using 'conf' configuration
optee api revision: 2.0
TEEC: Waring: Could not find security partition
## Verified-boot: 0
   Trying 'kernel' kernel subimage
     Description:  unavailable
     Type:         Kernel Image
     Compression:  uncompressed
     Data Start:   0x3acba400
     Data Size:    6908752 Bytes = 6.6 MiB
     Architecture: ARM
     OS:           Linux
     Load Address: 0x02008000
     Entry Point:  0x02008000
     Hash algo:    sha256
     Hash value:   f8370e30666db08c1b9427b87b63c3af13d0a7ac53bfcc4a5769f22f49355b26
   Verifying Hash Integrity ... sha256+ OK
## Loading ramdisk from FIT Image at 3aca1c00 ...
   Using 'conf' configuration
   Trying 'ramdisk' ramdisk subimage
     Description:  unavailable
     Type:         RAMDisk Image
     Compression:  uncompressed
     Data Start:   0x3b351000
     Data Size:    6971008 Bytes = 6.6 MiB
     Architecture: ARM
     OS:           Linux
     Load Address: 0x0a200000
     Entry Point:  unavailable
     Hash algo:    sha256
     Hash value:   74caf52476838e9543d940366cba66451c5ec18046145c108f43ce7bea346f4b
   Verifying Hash Integrity ... sha256+ OK
   Loading ramdisk from 0x3b351000 to 0x0a200000
## Loading fdt from FIT Image at 3aca1c00 ...
   Using 'conf' configuration
   Trying 'fdt' fdt subimage
     Description:  unavailable
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x3aca2400
     Data Size:    98222 Bytes = 95.9 KiB
     Architecture: ARM
     Load Address: 0x08300000
     Hash algo:    sha256
     Hash value:   4060343ebd33cab851657d88d1c7ae885ed3bf34160b1cbb6d0cff3c9b804003
   Verifying Hash Integrity ... sha256+ OK
   Loading fdt from 0x08300000 to 0x08300000
   Booting using the fdt blob at 0x08300000
   Loading Kernel Image from 0x3acba400 to 0x02008000 ... OK
  'reserved-memory' ramoops@8000000: addr=8000000 size=100000
   Using Device Tree in place at 08300000, end 0831afad
Adding bank: 0x00000000 - 0x08400000 (size: 0x08400000)
Adding bank: 0x08648000 - 0x40000000 (size: 0x379b8000)
Total: 1248.558 ms

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0xf00
[    0.000000] Linux version 4.19.111 (ubuntu@ubuntu) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05)) #2 SMP PREEMPT Sun Mar 24 07:32:11 PDT 2024
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: rp-rv1126
[    0.000000] earlycon: uart8250 at MMIO32 0xff570000 (options '')
[    0.000000] bootconsole [uart8250] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'drm-logo@00000000': base 0x00000000, size 0 MiB
[    0.000000] Reserved memory: created CMA memory pool at 0x3f800000, size 8 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x2f800000, size 256 MiB
[    0.000000] OF: reserved mem: initialized node isp, compatible id shared-dma-pool
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] percpu: Embedded 15 pages/cpu s32204 r8192 d21044 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 259512
[    0.000000] Kernel command line: user_debug=31 storagemedia=sd androidboot.storagemedia=sd androidboot.mode=normal  rw rootwait loglevel=7 earlycon=uart8250,mmio32,0xff570000 console=ttyFIQ0 root=PARTUUID=614e0000-0000 rootfstype=ext4 snd_aloop.index=7
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 743964K/1046240K available (9216K kernel code, 393K rwdata, 2196K rodata, 1024K init, 299K bss, 31940K reserved, 270336K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)
[    0.000000]     lowmem  : 0xb0000000 - 0xf0000000   (1024 MB)
[    0.000000]     pkmap   : 0xafe00000 - 0xb0000000   (   2 MB)
[    0.000000]     modules : 0xaf000000 - 0xafe00000   (  14 MB)
[    0.000000]       .text : 0x(ptrval) - 0x(ptrval)   (10208 kB)
[    0.000000]       .init : 0x(ptrval) - 0x(ptrval)   (1024 kB)
[    0.000000]       .data : 0x(ptrval) - 0x(ptrval)   ( 394 kB)
[    0.000000]        .bss : 0x(ptrval) - 0x(ptrval)   ( 300 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000]  Tasks RCU enabled.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] random: random: get_random_bytes called from start_kernel+0x328/0x4ac with crng_init=0
[    0.000000] clk: failed to reparent cpll to clk_osc0_div32k: -22
[    0.000000] clk: failed to reparent cpll to clk_osc0_div32k: -22
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.008185] Switching to timer-based delay loop, resolution 41ns
[    0.015349] Console: colour dummy device 80x30
[    0.019962] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[    0.030454] pid_max: default: 4096 minimum: 301
[    0.035236] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.042024] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.049660] CPU: Testing write buffer coherency: ok
[    0.054963] /cpus/cpu@f00 missing clock-frequency property
[    0.060596] /cpus/cpu@f01 missing clock-frequency property
[    0.066231] /cpus/cpu@f02 missing clock-frequency property
[    0.071891] /cpus/cpu@f03 missing clock-frequency property
[    0.077502] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00
[    0.083948] Setting up static identity map for 0x100000 - 0x100060
[    0.090435] rcu: Hierarchical SRCU implementation.
[    0.095865] smp: Bringing up secondary CPUs ...
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot
[    0.108930] CPU1: thread -1, cpu 1, socket 15, mpidr 80000f01
[    0.117434] CPU2: thread -1, cpu 2, socket 15, mpidr 80000f02
[    0.125897] CPU3: thread -1, cpu 3, socket 15, mpidr 80000f03
[    0.126011] smp: Brought up 1 node, 4 CPUs
[    0.147833] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[    0.154256] CPU: All CPU(s) started in SVC mode.
[    0.159633] devtmpfs: initialized
[    0.182615] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.182764] Unpacking initramfs...
[    0.191057] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.204605] futex hash table entries: 16 (order: -2, 1024 bytes)
[    0.211314] pinctrl core: initialized pinctrl subsystem
[    0.217974] NET: Registered protocol family 16
[    0.223344] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.232413] cpuidle: using governor menu
[    0.236672] Registered FIQ tty driver
[    0.241234] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.249805] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.257816] console [pstore-1] enabled
[    0.262106] pstore: Registered ramoops as persistent store backend
[    0.268768] ramoops: attached 0x100000@0x8000000, ecc: 0/0
[    0.313426] cryptd: max_cpu_qlen set to 1000
[    0.318833] fiq debugger fiq mode enabled
[[    0.323619] console [ttyFIQ0] enabled
    0.323619] console [ttyFIQ0] enabled
[    0.331262] bootconsole [uart8250] disabled
[    0.331262] bootconsole [uart8250] disabled
[    0.336053] Registered fiq debugger ttyFIQ0
[    0.336608] rockchip-pm rockchip-suspend: not set pwm-regulator-config
[    0.339163] rk_iommu ffb00f00.iommu: version = 1
[    0.339679] rk_iommu ffb20800.iommu: version = 1
[    0.340036] rk_iommu ffb60e00.iommu: version = 1
[    0.340545] rk_iommu ffb80480.iommu: version = 1
[    0.340998] rk_iommu ffb90800.iommu: version = 1
[    0.341382] rk_iommu ffbb0f00.iommu: version = 1
[    0.342173] SCSI subsystem initialized
[    0.342430] usbcore: registered new interface driver usbfs
[    0.342546] usbcore: registered new interface driver hub
[    0.342668] usbcore: registered new device driver usb
[    0.342753] media: Linux media interface: v0.10
[    0.342814] videodev: Linux video capture interface: v2.00
[    0.342868] pps_core: LinuxPPS API ver. 1 registered
[    0.342886] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.342920] PTP clock support registered
[    0.344105] Advanced Linux Sound Architecture Driver Initialized.
[    0.344694] Bluetooth: Core ver 2.22
[    0.344770] NET: Registered protocol family 31
[    0.344790] Bluetooth: HCI device and connection manager initialized
[    0.344814] Bluetooth: HCI socket layer initialized
[    0.344834] Bluetooth: L2CAP socket layer initialized
[    0.344880] Bluetooth: SCO socket layer initialized
[    0.345284] rockchip-cpuinfo cpuinfo: SoC            : 11260000
[    0.345312] rockchip-cpuinfo cpuinfo: Serial         : 82dfcceb2509c3e7
[    0.346172] clocksource: Switched to clocksource arch_sys_counter
[    0.357148] NET: Registered protocol family 2
[    0.357836] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[    0.357883] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.358000] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.358150] TCP: Hash tables configured (established 8192 bind 8192)
[    0.358277] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.358336] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.358539] NET: Registered protocol family 1
[    0.359143] RPC: Registered named UNIX socket transport module.
[    0.359168] RPC: Registered udp transport module.
[    0.359183] RPC: Registered tcp transport module.
[    0.359200] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.360803] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.362954] Initialise system trusted keyrings
[    0.363167] workingset: timestamp_bits=29 max_order=18 bucket_order=0
[    0.369080] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.369853] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.370069] ntfs: driver 2.1.32 [Flags: R/O].
[    0.372453] Key type asymmetric registered
[    0.372484] Asymmetric key parser 'x509' registered
[    0.372549] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[    0.372571] io scheduler noop registered
[    0.372587] io scheduler deadline registered
[    0.372640] io scheduler cfq registered (default)
[    0.372659] io scheduler mq-deadline registered
[    0.372675] io scheduler kyber registered
[    0.372860] io scheduler bfq registered
[    0.376388] phy phy-ff4c0000.usb2-phy.1: Failed to get VBUS supply regulator
[    0.381536] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    0.381649] pwm-backlight backlight: Linked as a consumer to regulator.0
[    0.381744] pwm-backlight backlight: Dropping the link to regulator.0
[    0.381924] mpp_service mpp-srv: 29feab89b author: lixin 2022-04-25 Patch v2.2
[    0.381950] mpp_service mpp-srv: probe start
[    0.382754] iommu: Adding device ffb80000.rkvdec to group 3
[    0.382799] mpp_rkvdec ffb80000.rkvdec: Linked as a consumer to ffb80480.iommu
[    0.383011] mpp_rkvdec ffb80000.rkvdec: probing start
[    0.383530] mpp_rkvdec ffb80000.rkvdec: shared_niu_a is not found!
[    0.383556] rkvdec_init:1190: No niu aclk reset resource define
[    0.383578] mpp_rkvdec ffb80000.rkvdec: shared_niu_h is not found!
[    0.383594] rkvdec_init:1193: No niu hclk reset resource define
[    0.383844] mpp_rkvdec ffb80000.rkvdec: probing finish
[    0.384508] iommu: Adding device ffbb0000.rkvenc to group 5
[    0.384565] mpp_rkvenc ffbb0000.rkvenc: Linked as a consumer to ffbb0f00.iommu
[    0.384805] mpp_rkvenc ffbb0000.rkvenc: probing start
[    0.385270] mpp_rkvenc ffbb0000.rkvenc: venc regulator not rNAME=Buildroot
VeERSION=2018.02-rc3-g50dbe2f54-dirty
ID=buildroot
VERSION_ID=2018.02-rc3
PRETTY_NAME="Buildroot 2018.02-rc3"
ady, Starting logging: retry
OK   0.385296] rkvenc_init:1202: failed to add venc devfreq

[    0.386258] iommu: Adding devic/etc/init.d/S04alsa: line 22: alsactl: not found
e ffb90400.vdpu to group 4
[    0.386307] mpp_vdpu2 ffb90400.vdpu: Linked as a consumer to ffb90800.iommu
[    0.3Populating /dev using udev: 86397] mpp_vdpu2 ffb90400.vdpu: probe device
[    0.386827] mpp_vdpu2 ffb90400.vdpu: reset_group->rw_sem_on=0
[    0.386867] mpp_vdpu2 ffb90400.vdpu: reset_group->rw_sem_on=0
[    0.387060] mpp_vdpu2 ffb90400.vdpu: probing finish
[    0.387607] iommu: Adding device ffb90000.vepu to group 4
[    0.387652] mpp_vepu2 ffb90000.vepu: Linked as a consumer to ffb90800.iommu
[    0.387757] mpp_vepu2 ffb90000.vepu: probe device
[    0.388177] mpp_vepu2 ffb90000.vepu: reset_group->rw_sem_on=0
[    0.388211] mpp_vepu2 ffb90000.vepu: reset_group->rw_sem_on=0
[    0.388434] mpp_vepu2 ffb90000.vepu: probing finish
[    0.388891] iommu: Adding device ffb20000.iep to group 1
[    0.388939] mpp-iep2 ffb20000.iep: Linked as a consumer to ffb20800.iommu
[    0.389023] mpp-iep2 ffb20000.iep: probe device
[    0.389611] mpp-iep2 ffb20000.iep: allocate roi buffer failed
[    0.389787] mpp-iep2 ffb20000.iep: probing finish
[    0.390017] mpp_service mpp-srv: probe success
[    0.394078] dma-pl330 ff4e0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.394120] dma-pl330 ff4e0000.dma-controller:       DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[    0.395862] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[    0.396733] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[    0.397419] ff410000.serial: ttyS1 at MMIO 0xff410000 (irq = 31, base_baud = 1500000) is a 16550A
[    0.398063] ff560000.serial: ttyS0 at MMIO 0xff560000 (irq = 34, base_baud = 1500000) is a 16550A
[    0.398644] ff580000.serial: ttyS3 at MMIO 0xff580000 (irq = 35, base_baud = 1500000) is a 16550A
[    0.399168] ff590000.serial: ttyS4 at MMIO 0xff590000 (irq = 36, base_baud = 1500000) is a 16550A
[    0.399760] ff5a0000.serial: ttyS5 at MMIO 0xff5a0000 (irq = 37, base_baud = 1500000) is a 16550A
[    0.401538] random: fast init done
[    0.401881] random: crng init done
[    0.402322] iommu: Adding device ffb00000.vop to group 0
[    0.402371] rockchip-vop ffb00000.vop: Linked as a consumer to ffb00f00.iommu
[    0.405281] rockchip-drm display-subsystem: Linked as a consumer to ffb00000.vop
[    0.407258] rockchip-drm display-subsystem: devfreq is not set
[    0.407641] rockchip-drm display-subsystem: bound ffb00000.vop (ops 0xb0a41000)
[    0.407679] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    0.407696] [drm] No driver support for vblank timestamp query.
[    0.407816] rockchip-drm display-subsystem: failed to parse loader memory
[    0.408452] [drm] Initialized rockchip 2.0.0 20140818 for display-subsystem on minor 0
[    0.413258] zram: Added device: zram0
[    0.416877] libphy: Fixed MDIO Bus: probed
[    0.416898] CAN device driver interface
[    0.418640] rockchip-pinctrl pinctrl: pin gpio3-14 aldone
ready requested by ff5b0000.spi; cannot claim for ffc40000.eInitialitzingh random numbere generator... rnet
[    0.418681] rockchip-pinctrl pinctrl: pin-110 (ffc40000.ethernet) status -22
[ done.
   0.418705] rockchip-pinctrl pinctrl:realpath: /dev/block/by-name/misc: No such file or directory
 could not request pin 110 (gpio3-14) from group rgmiim0-bus2  on device rockchip-pinctrl
[    0.418724] rk_gmaWill now mount call partitions in /etc/fs-tab
strings: : No such file or directory
dwmaNote: Create /.skip_fsck to skip fsck
 - The ccheck might take a while if didn't shutdown properly!
 ffc40000.ethernet: Error applying setting, reverse things back
[    0.418771] rk_gmac-dwmac: probe of ffc40000.ethernet failed with error -22
[    0.418993] PPP generic driver version 2.4.2
[    0.419206] PPP BSD Compression module registered
[    0.419229] PPP Deflate Compression module registered
[    0.419259] PPP MPPE Compression module registered
[    0.419276] NET: Registered protocol family 24
[    0.420719] dwc3 ffd00000.dwc3: Failed to get clk 'ref': -2
[    0.425731] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.425763] ehci-platform: EHCI generic platform driver
[    0.429346] ehci-platform ffe00000.usb: EHCI Host Controller
[    0.429409] ehci-platform ffe00000.usb: new USB bus registered, assigned bus number 1
[    0.429601] ehci-platform ffe00000.usb: irq 72, io mem 0xffe00000
[    0.442903] ehci-platform ffe00000.usb: USB 2.0 started, EHCI 1.00
[    0.443172] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[    0.443200] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.443219] usb usb1: Product: EHCI Host Controller
[    0.443237] usb usb1: Manufacturer: Linux 4.19.111 ehci_hcd
[    0.443254] usb usb1: SerialNumber: ffe00000.usb
[    0.443902] hub 1-0:1.0: USB hub found
[    0.443964] hub 1-0:1.0: 1 port detected
[    0.444564] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.444610] ohci-platform: OHCI generic platform driver
[    0.445138] ohci-platform ffe10000.usb: Generic Platform OHCI controller
[    0.445190] ohci-platform ffe10000.usb: new USB bus registered, assigned bus number 2
[    0.445343] ohci-platform ffe10000.usb: irq 73, io mem 0xffe10000
[    0.503803] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4Log saved to /tmp/mountall.log
.19
[    0.503835] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.503858] usb usb2: Product: Generic PlStarting network: atform OHCI controller
[    0.503876] usb usb2: Manufacturer: Linux 4.19.111 ohci_hcd
[    0.503894] usb usb2: SerialNumber: ffe10000.usb
[    0.504560] hub 2-0:1.0: USB hub found
[    0.504634] hub 2-0:1.0: 1 port detected
[    0.506063] usbcore: registered nOK
ew interface driver usb-storage
[    0.506350] usbcore: registered new interface driver option
[    0.506404] usbserial: USB Serial support registered for GSM modem Debug: configfs_init
(1-port)
[    0.507026] <<-GTP-INFO->> GTP driver installing...
[    0.507432] i2c /dev entries driver
[    0.509111] rk808 0-0020: chip id: 0x8090
[    0.509199] rk808 0-0020: No cache defaults, reading back from HW
[    0.515542] rk808 0-0020: source: on=0x10, off=0x00
[    0.515582] rk808 0-0020: support dcdc3 fb mode:-22, -1330096136
[  mkdir: can't create directory '/sys/kernel/config/usb_gadget/rockchip/functions/mtp.gs0': No such file or directory
  0.515606] rk808 0-0020: support pmic reset mode:0,0
[    0.519355] rk808-regumkdir: can't create directory '/sys/kernel/config/usb_gadget/rockchip/functions/arm.gs6': No sluch aile or ditrectoory
  rk808-regulator: there is no dvs0 gpio
[    0.5194mkdir: can't create directory '/sys/kernel/config/usb_gadget/rockchip/functions/mass_storage.0': No such file or directory
49] rk808-regulator rk808-regulator: there is no dvs1 gpio
[    0.519584] DCDCmkdir: can_'t cRreate directEory G'/sys/kernel/config/usb_gadget/rockchip/functions/hid.usb0': No such file or directory
1: supplied by vcc5v0_sys
[    0.520146] DCDC_REG2: supplied by vcc5v0_sys
[    0.520647] DCDC_REG3: supplied by vcc5v0_sys
[    0.521030] DCDC_REG4: supplied by vcc5v0_sys
[    0.521410] DCDC_REG5: supplied by vcc5v0_sys
[    0.521900] LDO_REG1: supplied by vcc_buck5
[    0.522381] LDO_REG2: supplied by vcc_buck5
[    0.522765] LDO_REG3: supplied by vcc_buck5
[    0.523196] LDO_REG4: supplied by vcc_buck5
[    0.523581] LDO_REG5: supplied by vcc_buck5
[    0.523968] LDO_REG6: supplied by vcc_buck5
[    0.524031] vcc_dvdd: Bringing 1100000uV into 1200000-1200000uV
[    0.524478] LDO_REG7: supplied by vcc5v0_sys
[    0.524863] LDO_REG8: supplied by vcc5v0_sys
[    0.525370] LDO_REG9: supplied by vcc5v0_sys
[    0.525844] SWITCH_REG1: supplied by vcc5v0_sys
[    0.526243] SWITCH_REG2: supplied by vcc3v3_sys
[    0.528106] input: rk805 pwrkey as /devices/platform/ff3f0000.i2c/i2c-0/0-0020/rk805-pwrkey/input/input0
[    0.530904] i2c i2c-1: 1 i2c clients have been registered at 0x36
[    0.532439] rockchip-mipi-csi2: probe success, v4l2_dev:(null)!
[    0.533675] rkcifhw ffae0000.rkcif: no iommu attached, using non-iommu buffers
[    0.533723] rkcifhw ffae0000.rkcif: assigned reserved memory node isp
[    0.533850] rkcif rkcif_dvp: rkcif driver version: v00.01.0a
[    0.533934] rkcif rkcif_dvp: attach to cif hw node
[    0.533955] rkcif rkcif_dvp: rkcif wait line 0
[    0.534799] rkcif_dvp: cif_subdev_notifier: no subdev be found!
[    0.534822] rkcif_dvp: Failed to register subdev notifier(-19)
[    0.535535] rkcif rkcif_dvp: detach to cif hw node
[    0.535634] rkcif rkcif_mipi_lvds: rkcif driver version: v00.01.0a
[    0.535713] rkcif rkcif_mipi_lvds: attach to cif hw node
[    0.535737] rkcif rkcif_mipi_lvds: rkcif wait line 0
[    0.536549] rkcif rkcif_mipi_lvds: Entity type for entity rockchip-mipi-csi2 was not initialized!
[    0.536570] rockchip-mipi-csi2: Async registered subdev
[    0.538511] rkisp_hw ffb50000.rkisp: is_thunderboot: 0
[    0.538547] rkisp_hw ffb50000.rkisp: Missing rockchip,grf property
[    0.538803] rkisp_hw ffb50000.rkisp: iommu is disabled, using non-iommu buffers
[    0.538836] rkisp_hw ffb50000.rkisp: assigned reserved memory node isp
[    0.539124] rkisp rkisp-vir0: rkisp driver version: v01.06.02
[    0.539317] rkisp rkisp-vir0: No memory-region-thunderboot specified
[    0.539549] rkisp rkisp-vir0: Entity type for entity rkisp-isp-subdev was not initialized!
[    0.539590] rkisp rkisp-vir0: Entity type for entity rkisp-csi-subdev was not initialized!
[    0.539614] rkisp rkisp-vir0: Entity type for entity rkisp-bridge-ispp was not initialized!
[    0.542625] iommu: Adding device ffb60000.rkispp to group 2
[    0.542686] rkispp_hw ffb60000.rkispp: Linked as a consumer to ffb60e00.iommu
[    0.543098] rkispp_hw ffb60000.rkispp: max input:0x0@0fps
[    0.543143] rkispp_hw ffb60000.rkispp: can't request region for resource [mem 0xffb60000-0xffb7ffff]
[    0.543349] rkispp_hw ffb60000.rkispp: failed to get cru reset
[    0.543622] rkispp rkispp-vir0: rkispp driver version: v01.06.02
[    0.545810] usbcore: registered new interface driver uvcvideo
[    0.545831] USB Video Class driver (1.1.1)
[    0.546291] rockchip-iodomain fe020000.syscon:io-domains: Linked as a consumer to regulator.16
[    0.546346] rockchip-iodomain fe020000.syscon:io-domains: vccio2(3300000 uV) supplied by vccio_sd
[    0.546449] rockchip-iodomain fe020000.syscon:io-domains: Linked as a consumer to regulator.12
[    0.546494] rockchip-iodomain fe020000.syscon:io-domains: vccio3(1800000 uV) supplied by vcc_1v8
[    0.546597] rockchip-iodomain fe020000.syscon:io-domains: vccio4(1800000 uV) supplied by vcc_1v8
[    0.546697] rockchip-iodomain fe020000.syscon:io-domains: Linked as a consumer to regulator.19
[    0.546741] rockchip-iodomain fe020000.syscon:io-domains: vccio5(3300000 uV) supplied by vcc_3v3
[    0.546889] rockchip-iodomain fe020000.syscon:io-domains: vccio6(3300000 uV) supplied by vcc_3v3
[    0.547005] rockchip-iodomain fe020000.syscon:io-domains: vccio7(1800000 uV) supplied by vcc_1v8
[    0.547106] rockchip-iodomain fe020000.syscon:io-domains: Linked as a consumer to regulator.10
[    0.547146] rockchip-iodomain fe020000.syscon:io-domains: pmuio0(1800000 uV) supplied by vcc1v8_pmu
[    0.547252] rockchip-iodomain fe020000.syscon:io-domains: Linked as a consumer to regulator.7
[    0.547292] rockchip-iodomain fe020000.syscon:io-domains: pmuio1(3300000 uV) supplied by vcc3v3_sys
[    0.549720] rockchip-thermal ff5f0000.tsadc: tsadc trimmed value = -3
[    0.550023] rockchip-thermal ff5f0000.tsadc: tsadc is probed successfully!
[    0.550414] rockchip-thermal ff5f8000.tsadc: tsadc trimmed value = -2
[    0.550656] rockchip-thermal ff5f8000.tsadc: tsadc is probed successfully!
[    0.551406] Bluetooth: HCI UART driver ver 2.3
[    0.551434] Bluetooth: HCI UART protocol H4 registered
[    0.551681] cpu cpu0: bin=0
[    0.551727] cpu cpu0: leakage=1.625
[    0.551849] cpu cpu0: Linked as a consumer to regulator.5
[    0.563530] cpu cpu0: temp=30200, pvtm=98500 (98220 + 280)
[    0.563653] cpu cpu0: pvtm-volt-sel=1
[    0.563735] cpu cpu0: Dropping the link to regulator.5
[    0.563793] cpu cpu0: bin-scale=5
[    0.564162] cpu cpu0: Linked as a consumer to regulator.5
[    0.564238] cpu cpu0: Dropping the link to regulator.5
[    0.564439] cpu cpu0: Linked as a consumer to regulator.5
[    0.565327] cpu cpu0: avs=0
[    0.565682] cpu cpu0: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 h_table=0
[    0.565721] cpu cpu0: failed to read out thermal zone (-22)
[    0.566736] cpu cpu0: failed to find power_model node
[    0.566818] cpuidle: enable-method property 'psci' found operations
[    0.566920] cpuidle: enable-method property 'psci' found operations
[    0.566990] cpuidle: enable-method property 'psci' found operations
[    0.567064] cpuidle: enable-method property 'psci' found operations
[    0.567735] Synopsys Designware Multimedia Card Interface Driver
[    0.568278] dwmmc_rockchip ffc50000.dwmmc: IDMAC supports 32-bit address mode.
[    0.568312] dwmmc_rockchip ffc50000.dwmmc: Using internal DMA controller.
[    0.568328] dwmmc_rockchip ffc50000.dwmmc: Version ID is 270a
[    0.568382] dwmmc_rockchip ffc50000.dwmmc: DW MMC controller at irq 67,32 bit host data width,256 deep fifo
[    0.568498] mmc_host mmc0: card is non-removable.
[    0.579716] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    0.592919] dwmmc_rockchip ffc60000.dwmmc: IDMAC supports 32-bit address mode.
[    0.592961] dwmmc_rockchip ffc60000.dwmmc: Using internal DMA controller.
[    0.592977] dwmmc_rockchip ffc60000.dwmmc: Version ID is 270a
[    0.593028] dwmmc_rockchip ffc60000.dwmmc: DW MMC controller at irq 68,32 bit host data width,256 deep fifo
[    0.593133] dwmmc_rockchip ffc60000.dwmmc: Linked as a consumer to regulator.17
[    0.593189] dwmmc_rockchip ffc60000.dwmmc: Linked as a consumer to regulator.16
[    0.606119] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    0.609604] mmc_host mmc0: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
[    0.619266] dwmmc_rockchip ffc70000.dwmmc: IDMAC supports 32-bit address mode.
[    0.619306] dwmmc_rockchip ffc70000.dwmmc: Using internal DMA controller.
[    0.619324] dwmmc_rockchip ffc70000.dwmmc: Version ID is 270a
[    0.619381] dwmmc_rockchip ffc70000.dwmmc: DW MMC controller at irq 69,32 bit host data width,256 deep fifo
[    0.619552] dwmmc_rockchip ffc70000.dwmmc: allocated mmc-pwrseq
[    0.619572] mmc_host mmc1: card is non-removable.
[    0.632409] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    0.639692] mmc_host mmc0: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0)
[    0.643576] hidraw: raw HID events driver (C) Jiri Kosina
[    0.644287] Freeing initrd memory: 6808K
[    0.644303] usbcore: registered new interface driver usbhid
[    0.644313] usbhid: USB HID core driver
[    0.645550] rockchip-saradc ff5e0000.saradc: Linked as a consumer to regulator.12
[    0.645978] rksfc_base v1.1 2016-01-08
[    0.646303] rksfc ffc90000.sfc: rksfc_probe clk rate = 79200000
[    0.646373] rkflash_dev_init enter
[    0.646413] sfc nor id: 0 0 0
[    0.646425] rkflash[1] is invalid
[    0.646428] rkflash_dev_init enter
[    0.646448] sfc_nand id: 0 0 0
[    0.646456] rkflash[2] is invalid
[    0.647004] rp_gpio prepare build 5 gpio
[    0.647052] rp_gpio request vdd5v_3v3
[    0.647073] success request gpio0 out
[    0.647099] rp_gpio request hub_rst
[    0.647116] success request gpio102 out
[    0.647140] rp_gpio request usb_5v
[    0.647156] success request gpio129 out
[    0.647180] rp_gpio request spk_on
[    0.647196] success request gpio85 out
[    0.647217] rp_gpio request spk_mute
[    0.647233] success request gpio87 out
[    0.647364] input: gpio_event as /devices/platform/rp_power/input/input1
[    0.648755] rp_gpio prepare build 11 gpio
[    0.648814] rp_gpio request ir_led
[    0.648839] success request gpio77 out
[    0.648862] rp_gpio request bl_led
[    0.648877] success request gpio78 out
[    0.648902] rp_gpio request otg_host
[    0.648917] success request gpio2 out
[    0.648942] rp_gpio request gpio3c2
[    0.648957] success request gpio114 out
[    0.648981] rp_gpio request gpio2b4
[    0.648996] success request gpio76 out
[    0.649020] rp_gpio request gpio2b7
[    0.649036] success request gpio79 out
[    0.649060] rp_gpio request gpio2c1
[    0.649072] success request gpio81 out
[    0.649096] rp_gpio request gpio2c2
[    0.649111] success request gpio82 out
[    0.649135] rp_gpio request gpio2c3
[    0.649149] success request gpio83 out
[    0.649173] rp_gpio request gpio2c4
[    0.649188] success request gpio84 out
[    0.649212] rp_gpio request gpio2c6
[    0.649227] success request gpio86 out
[    0.650515] usbcore: registered new interface driver snd-usb-audio
[    0.651702] rk817-codec rk817-codec: DMA mask not set
[    0.657934] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
[    0.658052] NET: Registered protocol family 17
[    0.658083] NET: Registered protocol family 15
[    0.658133] can: controller area network core (rev 20170425 abi 9)
[    0.658211] NET: Registered protocol family 29
[    0.658229] can: raw protocol (rev 20170425)
[    0.658242] can: broadcast manager protocol (rev 20170425 t)
[    0.658259] can: netlink gateway (rev 20170425) max_hops=1
[    0.658501] Bluetooth: RFCOMM TTY layer initialized
[    0.658533] Bluetooth: RFCOMM socket layer initialized
[    0.658568] Bluetooth: RFCOMM ver 1.11
[    0.658589] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    0.658607] Bluetooth: HIDP socket layer initialized
[    0.658619] [BT_RFKILL]: Enter rfkill_rk_init
[    0.658631] [WLAN_RFKILL]: Enter rfkill_wlan_init
[    0.659025] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[    0.659079] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6255
[    0.659094] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[    0.659108] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[    0.659182] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,host_wake_irq = 8, flags = 0.
[    0.659216] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[    0.659230] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[    0.659907] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 48.
[    0.659994] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,power_gpio = 7.
[    0.660219] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 5.
[    0.660261] [BT_RFKILL]: bluetooth_platdata_parse_dt: clk_get failed!!!.
[    0.660325] [BT_RFKILL]: Request irq for bt wakeup host
[    0.660466] [BT_RFKILL]: ** disable irq
[ /etc/init.d/rcS: line 26: /etc/init.d /S85ipc-display-co nfig: not found
 0.660627] [BT_RFKILL]: bt_default device registered.
[    0.661778] Startinfg input-event-daemonl: ash vendor_init_thread!
[    0.661811] flash vinput-event-daemon:e Start parsing /etc/input-event-daemon.conf...
ndoinput-event-daemon: Adding device: /devr/input/event0...
input-event-daem on: Adding device: /dev/insput/event1...
inputt-event-daemon: Adding device: /dev/input/event2...
input-event-daemon: Adding device: /dev/input/event3...
input-event-daemon: Start listening on 4 devices...
orage:20done
170308 ret = -1
[    0.662284] Registering SWP/SWPB emulation handler
[    0.662783] Loading compiled-in X.509 certificates
[    0.663848] rga2: D[root@RV1126_RV1109:/]# river loaded successfully ver:3.2.56726
[    0.664132] rga2: Module initialized.
[    0.668505] mmc_host mmc1: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
[    0.669624] mmc_host mmc0: Bus speed (slot 0) = 100000Hz (slot req 100000Hz, actual 100000HZ div = 0)
[    0.683669] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    0.683731] pwm-backlight backlight: Linked as a consumer to regulator.0
[    0.683787] pwm-backlight backlight: Dropping the link to regulator.0
[    0.684155] mpp_rkvenc ffbb0000.rkvenc: probing start
[    0.684735] mpp_rkvenc ffbb0000.rkvenc: Linked as a consumer to regulator.4
[    0.684785] mpp_rkvenc ffbb0000.rkvenc: bin=0
[    0.684807] mpp_rkvenc ffbb0000.rkvenc: leakage=1.375
[    0.684847] mpp_rkvenc ffbb0000.rkvenc: Failed to get pvtm
[    0.684870] mpp_rkvenc ffbb0000.rkvenc: bin-scale=37
[    0.685136] mpp_rkvenc ffbb0000.rkvenc: avs=0
[    0.685339] mpp_rkvenc ffbb0000.rkvenc: failed to find power_model node
[    0.685354] mpp_rkvenc ffbb0000.rkvenc: failed to initialize power model
[    0.685471] mpp_rkvenc ffbb0000.rkvenc: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 h_table=0
[    0.685492] mpp_rkvenc ffbb0000.rkvenc: failed to read out thermal zone (-22)
[    0.685928] mpp_rkvenc ffbb0000.rkvenc: probing finish
[    0.686413] input: adc-keys as /devices/platform/adc-keys/input/input2
[    0.687382] asoc-simple-card pdm-mic_array: dummy-codec <-> ff830000.pdm mapping ok
[    0.688614] asoc-simple-card rk809-sound: ASoC: DAPM unknown pin Headphones
[    0.691048] asoc-simple-card rk809-sound: rk817-hifi <-> ff800000.i2s mapping ok
[    0.691085] asoc-simple-card rk809-sound: ASoC: no source widget found for MICBIAS1
[    0.691099] asoc-simple-card rk809-sound: ASoC: Failed to add route MICBIAS1 -> direct -> Mic Jack
[    0.691110] asoc-simple-card rk809-sound: ASoC: no sink widget found for IN1P
[    0.691121] asoc-simple-card rk809-sound: ASoC: Failed to add route Mic Jack -> direct -> IN1P
[    0.691132] asoc-simple-card rk809-sound: ASoC: no source widget found for HPOL
[    0.691142] asoc-simple-card rk809-sound: ASoC: Failed to add route HPOL -> direct -> Headphone Jack
[    0.691153] asoc-simple-card rk809-sound: ASoC: no source widget found for HPOR
[    0.691164] asoc-simple-card rk809-sound: ASoC: Failed to add route HPOR -> direct -> Headphone Jack
[    0.691617] input: rockchip,rk809-codec Headphones as /devices/platform/rk809-sound/sound/card1/input3
[    0.692685] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    0.692760] pwm-backlight backlight: Linked as a consumer to regulator.0
[    0.692818] pwm-backlight backlight: Dropping the link to regulator.0
[    0.693467] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    0.693539] pwm-backlight backlight: Linked as a consumer to regulator.0
[    0.693597] pwm-backlight backlight: Dropping the link to regulator.0
[    0.694466] rkcif rkcif_mipi_lvds: clear unready subdev num: 1
[    0.694485] rockchip-mipi-dphy-rx: No link between dphy and sensor
[    0.694710] rockchip-mipi-dphy-rx: No link between dphy and sensor
[    0.694728] rkcif_mipi_lvds: Async subdev notifier completed
[    0.695118] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    0.700748] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    0.701120] rkisp rkisp-vir0: clear unready subdev num: 1
[    0.701308] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    0.701321] cfg80211: failed to load regulatory.db
[    0.701563] rockchip-mipi-dphy-rx: No link between dphy and sensor
[    0.701577] rockchip-mipi-dphy-rx: No link between dphy and sensor
[    0.701593] rkisp0: Invalid mipi data type
[    0.701601] rkisp0: update sensor failed
[    0.701669] ALSA device list:
[    0.701679]   #0: rockchip,pdm-mic-array
[    0.701686]   #1: rockchip,rk809-codec
[    0.702491] Freeing unused kernel memory: 1024K
[    0.702633] Run /init as init process
[    0.709358] mmc_host mmc1: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0)
[    0.749531] mmc_host mmc1: Bus speed (slot 0) = 100000Hz (slot req 100000Hz, actual 100000HZ div = 0)
[    0.774266] udevd[112]: starting version 3.2.7
[    0.776890] udevd[112]: specified group 'kvm' unknown
[    0.783302] udevd[113]: starting eudev-3.2.7
[    0.839544] asoc-simple-card rk809-sound: ASoC: DAPM unknown pin Headphones
[    0.930522] rockchip-mipi-dphy-rx: No link between dphy and sensor
[    0.931121] rockchip-mipi-dphy-rx: No link between dphy and sensor
[    0.939907] rockchip-mipi-dphy-rx: No link between dphy and sensor
[    0.943565] rockchip-mipi-dphy-rx: No link between dphy and sensor
[    0.943714] rockchip-mipi-dphy-rx: No link between dphy and sensor
[    1.180952] dwmmc_rockchip ffc60000.dwmmc: Busy; trying anyway
[    1.301449] file system registered
[    1.321024] using random self ethernet address
[    1.321053] using random host ethernet address
[    1.395907] read descriptors
[    1.395948] read strings
[    1.681003] mmc_host mmc2: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)
[    1.715746] mmc2: error -110 whilst initialising SD card
[    2.215816] dwmmc_rockchip ffc60000.dwmmc: Busy; trying anyway
[    2.715890] mmc_host mmc2: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)
[    2.716097] asoc-simple-card rk809-sound: ASoC: DAPM unknown pin Headphones
[    2.730055] mmc_host mmc2: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
[    3.230125] dwmmc_rockchip ffc60000.dwmmc: Busy; trying anyway
[    3.730172] mmc_host mmc2: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)
[    3.752935] vendor storage:20190527 ret = -1
[    4.230228] dwmmc_rockchip ffc60000.dwmmc: Busy; trying anyway
[    4.730281] mmc_host mmc2: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)
[    5.230343] dwmmc_rockchip ffc60000.dwmmc: Busy; trying anyway
[    5.730397] mmc_host mmc2: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)
[    5.730531] android_work: did not send uevent (0 0   (null))
[    6.247269] dwmmc_rockchip ffc60000.dwmmc: Busy; trying anyway
[    6.747415] mmc_host mmc2: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)
[    6.761446] mmc_host mmc2: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0)
[    7.287101] dwmmc_rockchip ffc60000.dwmmc: Busy; trying anyway
[    7.787202] mmc_host mmc2: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)
[    7.801396] mmc_host mmc2: Bus speed (slot 0) = 100000Hz (slot req 100000Hz, actual 100000HZ div = 0)
[    8.335466] dwmmc_rockchip ffc60000.dwmmc: Busy; trying anyway
[    8.835577] mmc_host mmc2: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)

[root@RV1126_RV1109:/]#
[root@RV1126_RV1109:/]#
[root@RV1126_RV1109:/]#
[root@RV1126_RV1109:/]# ls
bin             lib32           proc            timestamp
busybox.config  linuxrc         res             tmp
data            media           root            udisk
dev             misc            run             userdata
etc             mnt             sbin            usr
init            oem             sdcard          var
lib             opt             sys
[root@RV1126_RV1109:/]# uname -a
Linux RV1126_RV1109 4.19.111 #2 SMP PREEMPT Sun Mar 24 07:32:11 PDT 2024 armv7l GNU/Linux
[root@RV1126_RV1109:/]# cat /etc/issue[   32.139623] vcc18_lcd_n: disabling
[   32.139667] vcc_dovdd: disabling

Welcome to RV1126_RV1109 Buildroot
[root@RV1126_RV1109:/]#
